Fin-Set Materials Analysis for Heat Removal Utilizing ANSYS

Authors

  • Yogendra Singh Tomar SriRam College of Engineering and Management (SRCEM), Gwalior (M.P.), India
  • C.S. Kohli SriRam College of Engineering and Management (SRCEM), Gwalior (M.P.), India

DOI:

https://doi.org/10.37591/joarb.v3i1.626

Abstract

Present paper deals with the effect of fin material on heat transfer from fin for electronics device cooling. Electronic tools discharge heat in the course of the work; that discharged heat should be removed either by passive or active ways. Current work stresses on passive (natural) way of cooling. Natural cooling can be done either by free air or fin. Different types of fin materials have been studied in the present work to observe their effect on heat transfer. Electronic device which generated heat at a rate of 1.5 W was made of copper and container which enclosed the electronic device was considered to be made up of steel. Convective boundary conditions which represent the actual physical scenario have been considered at the outer walls. Heat transfer coefficient of convection in the atmosphere has been considered around h=40 W/m2 ºK and the ambient temperature was 27 ºC.

Keywords: Fin material, micro heat exchanger (MHE), heat transfer, finite element analysis (FEA), electronic device

 

Cite this Article
Tomar YS, Kohli CS. Fin-Set Materials Analysis for Heat Removal Utilizing ANSYS. Journal of Advancements in Robotics. 2016; 3(1): 24–30p.

References

Cheng HH, Huang DS, Lin MT. Heat dissipation design and analysis of high power LED array using the finite element method. Microelectron Reliab. 2012; 52: 905–11p.

Bahadur R, Cohen AB. Orthotropic thermal conductivity effect on cylindrical pin fin heat transfer. Int J Heat Mass Transf. 2007; 50: 1155–62p.

Bricault P, Dombsky M, Dowling A, et al. High power target developments at ISAC. Nuclear Instruments and Methods in Physics Research B. 2003; 204: 319–24p.

Elnggar MHA, Abdullah MZ, Mujeebu MA. Experimental Analysis and FEM Simulation for Desktop PC Cooling using Finned U-Shape Multi Heat Pipe. Energ Convers Manage. 2011; 52: 2937–44p.

Galvis E, Jubran BA, Behdinan FK, et al. Numerical Modelling of Pin–Fin Micro Heat Exchanger. Heat Mass Transfer. 2008; 44: 659–66p.

Husain A, Kim KY. Optimization of a Micro-Channel Heat Sink with Temperature Dependent Fluid Properties. Appl Therm Eng. 2008; 28: 1101–7p.

Islamoglu Y. Numerical Analysis of the Influence of a Circular Fin with Different Profiles on the Thermal Characteristics in a Ceramic Tube of Heat Transfer Equipment. Int J Pres Ves Pip. 2004; 81: 583–7p.

Kolluri S, Endo K, Suzuki E, et al. Modelling and Analysis of Self-Heating in Fin-FET Devices for Improved Circuit and EOS/ESD Performance. Proceedings of the IEEE Electron Devices Meeting; 2007 Dec 10–12; Washington, DC. 177–80p.

Zhang Q, Wang W, Zhang H, et al. Temperature Analysis of Continuous-Flow Micro-PCR based on FEA. Sensor Actuat B. 2002; 82: 75–81p.

Li Y, Xu Q. Designed and Analysis of a Totally Decoupled Flexure-Based XY Parallel Micromanipulator. IEEE T Robotic. 2009; 25(3): 645–57p.

Downloads

Published

2016-04-21

Issue

Vol. 3 No. 1 (2016)

Section

Research Articles

License

Declaration and Copyright Transfer Form

(to be completed by authors)

I/ We, the undersigned author(s) of the submitted manuscript, hereby declare, that the above manuscript which is submitted for publication in the STM Journals(s), is not published already in part or whole (except in the form of abstract) in any journal or magazine for private or public circulation, and, is not under consideration of publication elsewhere.

  • I/We will not withdraw the manuscript after 1 week of submission as I have read the Author Guidelines and will adhere to the guidelines.
  • I/We Author(s ) have niether given nor will give this manuscript elsewhere for publishing after submitting in STM Journal(s).
  • I/ We have read the original version of the manuscript and am/ are responsible for the thought contents embodied in it. The work dealt in the manuscript is my/ our own, and my/ our individual contribution to this work is significant enough to qualify for authorship.
  •  I/We also agree to the authorship of the article in the following order:

Author’s name                                    

 

1. ________________

2. ________________

3. ________________

4. ________________

 

We  Author(s) tick this box and would request you to consider it as our signature as we agree to the terms of this Copyright Notice, which will apply to this submission if and when it is published by this journal.